Problems with the Autowatch Ghost Immobiliser App?
If you’re having problems with the Autowatch Ghost Immobiliser app, don’t worry—we’re here to help.
Please note: The information on this page applies to the original Autowatch Ghost Immobiliser, which was discontinued around September 2018 and supported Bluetooth smartphone pairing.
The newer Autowatch Ghost II and Ghost III do not rely on the smartphone app in the same way, and we do not provide support for Bluetooth phone pairing on these systems due to the wide variation in mobile devices and operating systems. Where Bluetooth disarming is required, we recommend using a dedicated Bluetooth Tag.
Below are the most common questions and solutions for customers using the original Ghost app.
How do I pair my phone with the original Autowatch Ghost Immobiliser?
If you’re connecting your phone for the first time, follow the pairing guide below. We have also included a walkthrough video demonstrating the complete process.
Please follow each step carefully, as missing a step can prevent the pairing process from completing successfully.
Important: Where the instructions ask you to press and hold the accelerator pedal, some vehicles require a different input.
- Certain Jaguar and Land Rover vehicles require the main beam stalk to be held instead.
- Some Volkswagen Audi Group (VAG) vehicles require the hazard warning lights to be pressed and held.
If this applies to your vehicle, you should have been shown the correct procedure during installation.
Download the iPhone pairing guide below before starting.
Autowatch Ghost Immobiliser – How to use on iPhone (53 KB)
I’ve got a new phone and can’t pair it with my Ghost
If you’ve changed your phone and the Ghost will not pair with the new device, the most common cause is that the Ghost’s Bluetooth memory is already full.
In most cases, the stored pairing information simply needs to be cleared before your new phone can be connected.
Download the pairing instructions below and follow the Forced Removal process exactly as shown. We’ve also included a step-by-step walkthrough video further down this page.
If you’re unable to locate your service button, don’t worry. It will have been demonstrated when your Ghost was installed, and we’ve also produced a guide to help you identify it.
Again, if your vehicle uses an alternative button instead of the accelerator pedal (such as Jaguar, Land Rover or certain VAG models), use the correct button that was demonstrated during installation.
I’ve accidentally deleted the Bluetooth pairing
If you’ve removed the pairing from your phone by mistake, don’t panic.
Simply follow the Forced Removal process using the video below before pairing the phone again.
We’ve also included a full walkthrough video which takes you through the entire procedure step by step.
If you’re unsure where your service button is located, please refer to our Service Button guide before beginning.
My vehicle still starts even though the Ghost app isn’t running
If your vehicle still starts while your phone is nearby, even though the Ghost app has been closed, this is normally because the Ghost is still detecting the Bluetooth connection.
You’ll usually notice the normal double confirmation flash that you would receive after entering your PIN code manually.
Since the release of iOS 11, we’ve occasionally seen Apple devices continue broadcasting an active Bluetooth connection after the app has been closed.
The simplest solution is to perform a full restart of your iPhone.
If you regularly use Bluetooth disarming, we also recommend restarting your phone periodically and closing apps that are running in the background to help maintain a reliable Bluetooth connection.
My vehicle starts even when my phone isn’t nearby
If your vehicle starts without your phone being present and without receiving the normal confirmation flash, this is not normal behaviour.
Please contact us, as this could indicate a fault with the Ghost system. We’ll be happy to investigate the issue and, if necessary, arrange a warranty replacement.
Forced Removal Process
If you’re unable to pair your phone, have changed devices or need to clear the Ghost’s Bluetooth memory, follow the Forced Removal procedure using the guide below.
Please follow every step exactly as shown to ensure the process completes successfully.
Remember that certain Jaguar, Land Rover and VAG vehicles use alternative buttons instead of the accelerator pedal. If this applies to your vehicle, use the correct button combination that was demonstrated during installation.
The walkthrough video below also demonstrates the complete Forced Removal procedure from start to finish.
Need help with a newer Ghost Immobiliser?
If you’ve found this page while searching for help with a Ghost II or Ghost III, this guide is intended for the original Ghost system only.
For customers using a newer Ghost Immobiliser, please refer to our dedicated Ghost support pages or contact our team if you need further assistance.

